MTBOctoberFinale Ligure, Liguria, Italy

24H of Finale

WEMBO World Solo 24H Championship — Italian Riviera trails for one full rotation of the clock.

Official event page →

Distance

~250–300 km typical solo distance over 24 hours

Elevation

11,200 m climbing

Discipline

MTB

Character. The benchmark 24-hour MTB race globally and host of the WEMBO World Solo 24H Championship. 21+ editions, 3,000+ participants, held on Finale Ligure's famous coastal singletrack. Solo, duo and team categories; solo riders typically cover 250–300 km with 11,000 m of elevation over the 24 hours.

Conditions. Autumn Italian Riviera: 10–20 °C, dry typical, cool overnight hours, coastal air (humid but rarely raining).

Lube plan

If you wax — ZFC-recommended path. Pit-accessible ultra. Solo riders see their kit every lap, so the cleanest strategy is a pre-waxed spare chain for a swap in the night hours (when wear accumulates unseen). Recreational option: oil over wax during overnight rain or if the chain complains. Lap format makes either path easier than a linear ultra.

If you're on oil — pragmatic equivalent. The pit-lap format suits oil well — wipe and re-apply every 4-6 hours, especially before the night session. No chain swap drama; standard maintenance routine, just running through it more often than usual. Solo riders should pre-fill several pre-application doses (oil-soaked rags or a pre-measured dropper) so pit stops are quick.

Recommended lubricants

53 lubricants ranked · 9 excluded·Customise this scenario →

Staged recommendation

Ultra-endurance (single continuous push) — staged plan

A continuous ultra (Unbound XL, TCR, long solos) leaves two viable mid-event strategies. Option A: carry a pre-waxed spare chain and swap on course — maximum efficiency, zero post-event reset, ~150 g extra in the kit. Option B: carry a small oil bottle and apply over the wax when the chain goes dry — lighter kit, but you've committed to a chain-stripper degrease at home. Race vs recreational intent decides which. Wax emulsion drips are off the table either way — they need hours to cure that you simply don't have.

No wax emulsion drips mid-ultra. SS Drip, UFO Drip v2 etc. all need hours to set hard — you'll finish before they cure, meaning the top-up does nothing useful. Carry an oil (Synergetic) only.

Critical: Do NOT apply grease or heavy wet oils (Muc-Off Hydrodynamic, WD-40, generic mechanic's oils) to a waxed chain. Those contaminate deeply and create a much harder reset than a clean wet-ride oil like Synergetic.

1
Pre-event (24h+ before)
Wax the primary chain with a top immersive hot-melt
Race mode: wax a second identical chain in the same pot session so you have a spare ready to swap (see Option A below).
2
Event start
Start clean-waxed — ride out the wax for as long as it holds
On a fresh wax, expect 500–1000 km of clean performance on dry road, dropping to 150–300 km in heavy wet or extreme contamination. For a 1000 km+ ultra, assume the wax WILL run out before the finish — plan the mid-event action now.
3
Mid-event — Option A (race / max efficiency): chain swap
Swap to the pre-waxed spare chain on course
~90 seconds with a quick link. Zero post-event degrease — just put the used chain in a pouch, swap in the spare, keep riding. At home: re-wax the used chain like normal, both chains stay in the wax ecosystem. Carry: spare chain + master link / chain tool + rag + a small bag for the old chain (~150 g extra). Best for podium-chasing or efficiency-obsessed riders.
4
Mid-event — Option B (recreational / lighter pack): oil over wax
condition: wax depleted, rain, or sustained wet
Apply an oil over the wax — carry a small dripper bottle
Apply on the move or during a 30-second pause, continue immediately. Silca Synergetic is ZFC's published pick. Carries ~50 g vs ~150 g for Option A, but commits you to a chain-stripper solvent degrease at home (see stage 5). Wax emulsion drips (SS Drip, UFO Drip) are NOT viable mid-ultra — they need hours to cure that you don't have.
5
Post-event (only if Option B was used)
Chain-stripper solvent degrease, then re-wax
Wet-weather oil behaves like factory grease — boiling water and ultrasonic alone will not shift it. Use a proper chain stripper / solvent (mineral spirits, dedicated chain degreaser) with ultrasonic agitation. If you used Option A (chain swap), skip this stage — your used chain just gets re-waxed normally.

Tactics5 applicable · click any to expand

▸Portable wax pot for multi-day travel (hotel-based only)— Pack the Silca waxing station rather than a drip bottle — if the trip stays in powered accommodation.
when: Multi-day trips (stage race / training camp) with nightly hotel / apartment stops and car-supported logistics. NOT for tent / bivvy / wild-camp trips — the station is electric and needs mains power.
- The Silca waxing station is a compact mains-powered melt pot — fits in luggage, plugs into a hotel socket. Full melt in ~15 minutes.
- Requires electricity. Won't work at a camping trip (tent, bivvy, van without power) — fall back to the multi-pre-waxed-chains + emergency-oil strategy for those.
- Keeps you on your normal hot-melt workflow end-to-end — no compromise on wear, no drip-bottle decisions.
- Pair with the multi-chain rotation strategy: rotate to a fresh pre-waxed chain daily, re-wax the used ones at the hotel.
Highest-performance travel setup when you're hotel-hopping. Drop back to the drip-top-up / oil-rescue strategies for unpowered trips.
Silca Waxing System (mains-powered)·ZFC Waxing Zen Master Guide v4
▸Dry baseline + wet contingency for stage races— 2 hot-melt chains + Silca SS Drip for dusty days + Synergetic in reserve for rain.
when: Multi-day races with dry-but-rain-possible forecasts (BCBR, Unbound in a dry year, Italian training camps).
- Start each day on a waxed chain.
- Post-stage in dry + dusty conditions: top up with a wax emulsion drip (Silca SS Drip) when the chain demands it — don't worry about timing the set cycle. SSD's real-world 24 h set time is longer than a typical stage-race overnight (~12–16 h between stages), so the next morning's coat won't be fully hard. Apply anyway: a partial top-up on a waxed chain beats running it dry through another contaminated stage. After the trip, wipe the chain with a microfibre cloth + isopropyl alcohol (ZFC-recommended surface clean) and drop straight in your hot-melt pot. No solvent degrease required.
- Swap to fresh chain mid-week if a hard stage has clearly degraded the first one.
- Keep Silca Synergetic (an OIL, not a wax-compatible drip) in reserve for a rain day: ZFC's published advice is to apply it over the waxed chain and deal with the degrease at home. There is no such thing as a 'wax-compatible oil' — you're accepting the post-trip reset as the cost of keeping the chain lubricated through a wet ride.
- Avoid: Tru-Tension Tungsten All Weather. Field-calibration note: despite ZFC's 'top choice for waxers on holidays' write-up, real-world testing found it doesn't set hard like a proper wax emulsion drip — behaves more like Squirt, soft indefinitely. Set time matched SSD in practice, not the 'very short' the reviews describe.
- Synergetic is an oil. Applying it over wax is fine as a wet-ride rescue, but the chain cannot re-enter your hot-melt pot afterwards without a full degrease.
- Do NOT substitute heavy wet oils (Muc-Off Hydrodynamic, WD-40) — those contaminate deeply and create a much harder reset.
Silca Super Secret Drip review (Test 13)·Silca Synergetic review (Test 18)·Experienced-user field note (TT TAW, 2026-04-24)
▸Silca Super Secret Drip needs 24 h, not 12— Published set time of overnight / 12 h is optimistic in practice — plan for 24 h.
when: Multi-day scenarios where SSD is a realistic mid-trip top-up option.
- Real-world experience: if you apply SSD after a ride and race next morning, the coat is still tacky. 12 h is not enough; 24 h is closer to the truth.
- In a stage race you typically only have 12–16 h between stages, so you don't get to 'plan' a full set cycle — apply as the chain demands, accept the next morning's coat isn't fully hard, and know a partial top-up still beats running dry through another dusty or damp stage.
- If the scenario genuinely offers a full day of rest between rides (rest day mid-camp, planned weather buffer before a wet ride), wait 24 h rather than the published 12 h before committing the chain to that ride.
- SSD is still the top pot-compatible drip — this is a set-time nuance, not a compatibility one. No other pot-compatible drip has a proven shorter real-world set time; Tru-Tension Tungsten All Weather's 'very short' claim did not replicate in field testing.
Silca Super Secret Drip review (Test 13)·Experienced-user field note (2026-04-24)
▸SAL-only candidates — worth considering for long gravel— Some ZFC-tested waxes (Squirt Hot Wax, Silca Hot Melt + Endurance Chip variants) have exceptional single-application longevity but aren't in the main wear-block league table. On multi-day gravel, that's worth a second look.
when: Any stage-race or ultra-endurance gravel / MTB scenario where single-application longevity matters more than per-km wear differences.
- Squirt Hot Wax leads ZFC's single-application-longevity (SAL) test at 3,783 km real-world on dry road — further than Cyclowax Race Wax (3,033 km) or Silca Synerg-E (3,138 km).
- These lubes sit outside the main Block 1–6 wear league table because ZFC hasn't run them through the full protocol, so they're excluded from the ranked list above.
- For pure distance-per-wax events, an SAL winner can beat a Block-winner in practice — because the Block winner's wax runs out and you lose all its advantage.
- Worth checking the Excluded section at the bottom of the results, or searching ZFC's SAL data directly if you're optimising for longest uninterrupted wax life.
ZFC Single Application Longevity data (master XLSX)·Squirt Hot Wax review (YouTube)
▸Tru-Tension Tungsten All Weather — field calibration— ZFC's 'top choice for waxers on holidays' write-up did not replicate in field testing. Skip it — use Silca SS Drip for dusty top-ups instead.
when: Multi-day / ultra scenarios where TT TAW might be packed as a wax-compatible travel drip.
- ZFC's Test 12 review calls TT TAW a 'top choice to complement waxers going on holidays' with a 'very short' set time — implying apply-post-ride-ride-next-morning workflow.
- Field experience: never sets hard. Stays soft like Squirt indefinitely. Set time in practice matches Silca SS Drip (24 h), not 'very short'.
- Recommendation: don't pack it. Use Silca SS Drip for pot-compatible dusty top-ups and Silca Synergetic as the wet-day rescue (with planned post-trip degrease).
Tru-Tension Tungsten All Weather review (Test 12)·Experienced-user field note (2026-04-24)

Top recommendation · Cyclowax Race Wax

Loading expert commentary…

1
Cyclowax Race Wax
Immersive waxCompare →
91.7
score
50% B2 + 50% B4
0.031 wear
Single application
3,033 km
Approx. chain life
29,557 km
Cost / 6000 km
AUD 51
Why this rank
#1 because: damp offroad mixes dry dust with wet contamination — 50/50 split on Block 2 and Block 4. Cyclowax Race Wax is eligible after scenario filtering and its wear (0.031) is the lowest in the eligible set, which — given your priority weights — edges out every other eligible lube.
2
Rex Black Diamond Wax - 11+1 mix
Immersive waxCompare →
68.1
score
50% B2 + 50% B4
0.042 wear
Single application
—
Approx. chain life
13,453 km
Cost / 6000 km
AUD 112
Why this rank
#2 because: on 50% Block 2 + 50% Block 4 this lube's wear is 0.042 vs the top pick's 0.031 — Cyclowax Race Wax pulled ahead on the primary axis. Wear contributed most to this lube's own score.
3
Mspeedwax New Formula
Immersive waxZFC Tier 1Detail review →Compare →
50.1
score
50% B2 + 50% B4
0.060 wear
Single application
1,021 km
Approx. chain life
6,122 km
Cost / 6000 km
AUD 245
Why this rank
#3 because: on 50% Block 2 + 50% Block 4 this lube's wear is 0.059 vs the top pick's 0.031 — Cyclowax Race Wax pulled ahead on the primary axis. Wear contributed most to this lube's own score.
4
Silca Hot Melt
Immersive waxZFC Tier 1Detail review →Compare →
48.6
score
50% B2 + 50% B4
0.083 wear
Single application
640 km
Approx. chain life
21,898 km
Cost / 6000 km
AUD 69
Why this rank
#4 because: on 50% Block 2 + 50% Block 4 this lube's wear is 0.083 vs the top pick's 0.031 — Cyclowax Race Wax pulled ahead on the primary axis. Wear contributed most to this lube's own score.
5
Silca + Endurance Chip - *Extended intervals*
Immersive wax* Extended-interval testCompare →
42.1
score
50% B2 + 50% B4
0.094 wear
Single application
1,746 km
Approx. chain life
14,493 km
Cost / 6000 km
AUD 104
Why this rank
#5 because: on 50% Block 2 + 50% Block 4 this lube's wear is 0.094 vs the top pick's 0.031 — Cyclowax Race Wax pulled ahead on the primary axis. Wear contributed most to this lube's own score.
6
Rex Black Diamond Wax - 4+1 Mix
Immersive waxCompare →
39.9
score
50% B2 + 50% B4
0.099 wear
Single application
—
Approx. chain life
12,146 km
Cost / 6000 km
AUD 124
Why this rank
#6 because: on 50% Block 2 + 50% Block 4 this lube's wear is 0.099 vs the top pick's 0.031 — Cyclowax Race Wax pulled ahead on the primary axis. Wear contributed most to this lube's own score.
7
Optimize Bike
Wax-compatible dripWatch review →Compare →
36.3
score
50% B2 + 50% B4
0.119 wear
Single application
—
Approx. chain life
10,399 km
Cost / 6000 km
AUD 144
Why this rank
#7 because: on 50% Block 2 + 50% Block 4 this lube's wear is 0.118 vs the top pick's 0.031 — Cyclowax Race Wax pulled ahead on the primary axis. Wear contributed most to this lube's own score.
8
Silca Hot wax X
Immersive waxWatch review →Compare →
35.9
score
50% B2 + 50% B4
0.116 wear
Single application
1,350 km
Approx. chain life
9,967 km
Cost / 6000 km
AUD 151
Why this rank
#8 because: on 50% Block 2 + 50% Block 4 this lube's wear is 0.116 vs the top pick's 0.031 — Cyclowax Race Wax pulled ahead on the primary axis. Wear contributed most to this lube's own score.
9
Finish Line Halo IM wax (*RE-Test Jan 25)
Immersive waxWatch review →Compare →
33.3
score
50% B2 + 50% B4
0.167 wear
Single application
—
Approx. chain life
15,113 km
Cost / 6000 km
AUD 99
Why this rank
#9 because: on 50% Block 2 + 50% Block 4 this lube's wear is 0.167 vs the top pick's 0.031 — Cyclowax Race Wax pulled ahead on the primary axis. Low faff contributed most to this lube's own score.
10
Ceramic Speed Ultra Endurance Wax
Immersive waxCompare →
28.7
score
50% B2 + 50% B4
0.172 wear
Single application
—
Approx. chain life
6,742 km
Cost / 6000 km
AUD 222
Why this rank
#10 because: on 50% Block 2 + 50% Block 4 this lube's wear is 0.172 vs the top pick's 0.031 — Cyclowax Race Wax pulled ahead on the primary axis. Low faff contributed most to this lube's own score.

Excluded for this event (9)

ab-graphene-lube — No ZFC wear data for the scenario-relevant test block.
Finish line Ceramic Wax (unable to extrapolate data) — No ZFC wear data for the scenario-relevant test block.
NO LUBRICANT — Baseline / control entry.
rex-black-diamond-plus-rds — No ZFC wear data for the scenario-relevant test block.
rex-wax-race-blend — No ZFC wear data for the scenario-relevant test block.
rex-wax-training-blend — No ZFC wear data for the scenario-relevant test block.
Shimano Factory Grease — No ZFC wear data for the scenario-relevant test block.
Squirt Hot Wax — No ZFC wear data for the scenario-relevant test block.
Wend Wax test 1 - stick only — No ZFC wear data for the scenario-relevant test block.